Krieghoff Barrel / Stock Stickers

£2.50
20% VAT incl.

Available Options

  • Model:BARREL-STICKER
Krieghoff Barrel / Stock Stickers
Available in Gold, Silver or White.

These high quality vinyl sticker with the "Krieghoff" text logo are designed to be transferred to your Krieghoff Barrels or Stock.

The stickers come as a set of two. So you can attach one either side of your barrels, or attach one to your barrel and one to your stock.

Size: 149mm x 17.5mm
Choose your colour from the drop-down menu above.

How to Apply your Stickers

Step 1 - Prepare It
Lay your sticker on a clean and flat surface with the backing tape (white side) face down and rub over the application tape (clear side) with your squeegee or credit card to ensure the application tape has a good bond to the vinyl letters.

Step 2 - Peel It
Check the positioning of where your sticker will go, so you're ready for the next stage.
Next, peel the application tape (clear side) away from the backing paper (white side). Your sticker letters will now be held by the application tape.
Carefully place the the application tape on to your barrels. Check the alignment as you place it down.

Step 3 - Rub It
While your sticker in laying on your barrels in position, start by rubbing over the application tape and letters gently, and then increase the pressure and firmly rub with your squeegee or credit card. Make sure you cover each letter thoroughly.

Step 4 - Remove It
Carefully peel away the application tape at an angle and corner to corner. The letters should all be transferred onto your barrel. If they are still attached to the application tape, lay the application tape back down and rub over the letter again with the squeegee or credit card. Now, try again until the whole sticker has been transferred.
Your new Krieghoff Barrel / Stock Sticker should now be in place and ready to show off.
If your letters are not coming away from the application tape as you're peeling the application tape off, lay the application tape back over the letter and use the squeegee to rub over the letter again.

Sticker Removal
If you decide to remove the stickers for any reason. Use some light heat such as a hair dryer to aid the removal. The adhesive is permanent but will not damage or mark your barrels. Do not use any abrasive materials or solvents to remove the stickers as this may cause damage to the finish of your barrels.

Postage
We send the Krieghoff Barrel & Stock Stickers with a piece of card to prevent the stickers from being damaged in transit.



You might also like...

1 x Recknagel Picatinny Rail Antonio Zoli 1900, Alu [..0089]2 x Recknagel Safety for Mauser K98 [30100-5000]1 x Recknagel Extended Rail Remington 700 Short [57250-0012]1 x Ex-Demo Steel Factory Choke Tube, K-80 #3 (08)1 x Recknagel One Piece Tip-off Mounts for Zeiss Rail [57045-0110]1 x Recknagel Fibre Optic Front Sight Bead 9.5mm [11024-4095]1 x Recknagel Picatinny Rail 404mm Blank, Alu [..0140]1 x Recknagel Ring Base for Rear Sight [16550-0185]1 x Recknagel Front Ramp [12000-0000]1 x Recknagel Front Sight Bead White [11442-0300]1 x VFG Barrel Cleaning Felts for 4-4.5mm (Box of 500)1 x ERATAC UNI-Interface Picatinny Rail, 35mm [T0903-0008]1 x Recknagel SECURA Safety for Remington 700 [30170-1200]1 x Bauer HD Series 8x25 Binoculars1 x Briley 20b Speed Wrench - For Krieghoff1 x Contessa Picatinny Rail - Sauer 404 (0 MOA)1 x Recknagel 19mm Dovetail Ring Mounts 30mm1 x Recknagel Grip Cap Flat with Small Edge [24020-0400]1 x Recknagel Grip Cap Domed Blank [24000-0400]1 x ERATAC Picatinny Extended Riser Mount (Nut)1 x Parker Hale Thread to 8-32 Thread Converter1 x Recknagel Weaver Bases - Browning A-Bolt III [57080-302T]1 x Recknagel Grip Cap Skeleton Rounded [24060-0100]1 x ERATAC 36mm Ring with UNI-Interface [03680-5736]1 x Recknagel Weaver/Picatinny Mounts for S&B Rail (QD Lever)1 x Recknagel Picatinny Rail 200mm Blank No Slots, Steel [..0000]1 x Holex TORX Screwdriver set of 7 [00062-5057]1 x Recknagel One Piece Tip-off Mounts for Swarovski [57553-0110]1 x ERATAC 30mm Ring with UNI-Interface [03680-5730]1 x Recknagel Weaver Bases - FFV Carl Gustaf 2000 [.-3028]1 x Recknagel Adaptor for Thermal and Night Vision Devices - 56mm1 x Recknagel Detachable Sling Swivel with Nut 20mm Loop, 8mm Stud1 x Recknagel QD Sling Swivel Socket - Slim Forearm [23115-5010]1 x ERATAC Offset UNI-Interface for Aimpoint Sight [T0970-0000]1 x WalkStool Comfort 65 (65cm/26in)1 x Recknagel Detachable Sling Swivel 25.4mm Loop - 6mm Stud1 x Recknagel Polyform Lever & Nut for Picatinny Mounts1 x Recknagel Detachable Magnum Sling Swivel 25.4mm Loop - 8mm Stud1 x Recknagel SOB Silencer ERA LOC Thread Bushing1 x Recknagel One Piece QD Tip-off Picatinny Ring Mount [57530-5110]1 x Contessa Picatinny Rail - Browning A Bolt 1 Short (0 MOA)1 x Recknagel Weaver/Picatinny Mount for Aimpoint Micro [57020-1200]1 x Recknagel 11mm Dovetail Ring Mounts 30mm [42230-0500]1 x Contessa Picatinny Blank Rail for Custom Rails (450mm)1 x Jones Gun Nut Kit1 x Recknagel QD Sling Swivel - Fixed Standard [23000-0000]
Manufacturers
Useful Information