Contessa Extended Picatinny Rail for Sako 75* / 85 X-Short
With 0 MOA
Fits Sako Models: 75 / 85
Fits Calibres: .204 Ruger / .222 Rem / .223 Rem
(Please always double check the action size as this is a guide for the action size)
Rail Length: - 190mm
Extension Rearwards: - 75mm
Distance between Bases: - 56mm
Height (BH) - 12mm
MOA - 0 MOA
Weight: - 220g
Material: - Steel
Code Ref: PH31/NV/0
Contents Supplied:
- 1x Steel Rail,
- 1x Wrench,
This Steel Picatinny Rail is precision made by Contessa Alessandro & C. s.n.c. The part is precision made to fit the rifle with exact dovetail spacing to fit to the rifle with the supplied wrench. This full length rail has two dovetail clamping blocks which attach to the tapered dovetails either side of the ejection port on your Sako rifle. This is the Extended Version designed to be used with scopes such as night vision, which need to be mounted rearwards for better eye relief.
You can't always tell which size Sako action you have from the calibre, so to check which rail fits your rifle all you need to do is measure the length between your two bases, i.e. measure the length of your ejection port.
If it's approx. 56mm you need the Sako X-Short Rail
74mm you need the Sako Short Rail.
If it's approx. 84mm you need the Sako Medium Rail.
If it's approx. 94mm you need the Sako Long Rail.
Distance Spacing: (distances between bases)
30mm (Dovetail Base) / 56mm / 30mm (Dovetail Base)
Other Models Available:
Sako 75/85 X-Short (0 MOA)
Sako 75/85 X-Short Adjustable (0 MOA)
Sako 75/85 X-Short Extended (0 MOA)
Sako 75/85 X-Short Extended / Adjustable (0 MOA)
Sako 75/85 Short Adjustable (0 MOA)
Sako 75/85 Short Extended (0 MOA)
Sako 75/85 Short Extended / Adjustable (0 MOA)
Sako 75/85 Medium (0 MOA)
Sako 75/85 Medium Adjustable (0 MOA)
Sako 75/85 Medium Extended (0 MOA)
Sako 75/85 Long (0 MOA)
Sako 75/85 Long Adjustable (0 MOA)
Fitting:
A common issue with the Sako rifles is that the taper on the rifle is not the same as the taper on the picatinny rail. Contessa have designed their rail to fit as accurately as possible, tested on a wide number of Sako 85 actions. We have discovered there are slight variations in the Sako rifle dovetails due to factory tolerances, so even just a 1/100 of a mm can mean a poor fit. A method we use to overcome this poor fit is to remove the recoil stud from the rail (This is usually glued in with thread locker by Contessa, you may need to heat the screw to release the bond). This should allow the rail to slide on further and tighter. If this doesn't overcome the problem, we do suggest to use Locktite where the rail dovetail surface contacts the rifle dovetail. This will ensure a solid hold. Bear in mind, any recoil actually pushes the rail forwards into the dovetail and recoil will not alone cause the rail to loosen.
* The older models of Sako with the tapered dovetail, even on the Sako 75, there are larger variations in the dovetail widths. So you may discover that the rail does not slide on fully flush with the back of the rifle. This again would require hand fitting to the rifle. If you need any advice on hand fitting please contact us.
The
Contessa Catalogue has the full range of products available. If you would like any help with parts or fitting, feel free to call us on 01978 66 00 01. We can offer advise on the best possible solution, and a high quality scope mounting service.
The
Contessa Catalogue is available to download online now.
