K-80 Standard Trigger - Steel

£110.00
20% VAT incl.


  • Model:TRIG-NS
This Trigger blade fits all new model K-80 guns. It is suitable for K-80 owners with a forward position blade fitted who need the trigger to sit further back. The Trigger blade fits all new model K-80 guns that have the trigger blade attached on a T-slot rail. Earlier guns had a dovetail. If you wish to fit a new trigger on an earlier gun then you will also need a trigger upgrade. This can be done in our Krieghoff Service facility. Normally we recommend that you send the receiver of your gun to have the trigger fitted. It is possible to fit the blade yourself but please note the instructions you can read by reading the installation Procedure.

Fitting:

The K80 trigger blade is adjustable for position along a slide. There are two set screws on the underside of the trigger blade. The screw socket takes a 1.27mm wrench, 0.050" or 1/20th inch imperial. Use a Krieghoff Trigger/Selector Wrench. The rearmost screw locks the blade onto the slide whilst the front screw locks the barrel selector positioned immediately in front of the trigger blade. There are two trigger blade types, standard position and forward position. The standard blade has both screws in front of the curved blade whilst the forward position trigger has one screw in front and one directly behind the blade. Function of the two screws is the same.

To move the trigger blade, slacken the rear screw but note that the front screw, if locked, will also lock the trigger blade. The front screw has to be far enough out to allow the blade to slide so if it will not move try backing that screw out some more. Occasionally, the blade will be stuck on the slide but is easily freed with a nylon drift. Make sure both screws are free before tapping the blade with anything. Once in position, tighten the rearmost screw to lock the blade on the slide.

To lock the selector, tighten the front screw until the selector cannot be switched left to right. To release the selector, simply slacken that screw off again.

We Can Only Accept Orders from UK & Ireland Only
Please Note: This Product is only permitted to be sold in the UK and Ireland from this website. Any International Orders will be cancelled and refunded. You will be contacted if this is the case. If you would like to order Krieghoff parts, please contact your national distributor.


Watch the Trigger Replacement Instructional Video here:



You might also like...

1 x VFG Barrel Cleaning Felts for .22 (Box of 80)3 x Contessa Picatinny Rail - Sako S20 (20 MOA)3 x VFG Complete Set for .1771 x VFG Wipe Length Stopper & Guide for Rifles2 x Contessa Lightweight Alu Picatinny Rings - 40mm (8mm BH)2 x ERATAC Bubble Level [T0940-0002]1 x Krieghoff Shell Bag1 x VFG Barrel Cleaning Felts for .44 (Box of 30)3 x Contessa Picatinny Rail - Sako S20 (0 MOA) - Extended3 x VFG Pull Through Pocket Set for .22 Upwards1 x Krieghoff "K" Bobble Beanie - Royal Blue1 x Contessa Blued Steel Tactical Picatinny Rings - 30mm (10mm BH)1 x Contessa Blued Steel Picatinny Rings - 40mm (14.5mm BH)1 x Contessa QD Low Mount for Pulsar Night Vision (Picatinny)1 x VFG Barrel Cleaning Felts for 6.5mm (Box of 50)1 x Contessa Lightweight Alu Picatinny Rings - 34mm (8mm BH)1 x VFG Barrel Cleaning Felts for .22 (Box of 500)1 x VFG Barrel Cleaning Felts for .375 (Box of 500)1 x VFG Barrel Cleaning Felts for 7mm (Box of 500)1 x Contessa Tactical One Piece QD Picatinny Ring Mount 30mm, 0 MOA1 x Contessa Picatinny Extended Rail - Blaser R8/R93 (0 MOA)1 x Krieghoff "K" Mesh Cap - Grey1 x VFG Barrel Cleaning Felts for 6mm (Box of 500)1 x ERATAC 36mm Ring with UNI-Interface [03680-5736]1 x VFG Barrel Cleaning Felts for 8.5mm (Box of 50)1 x ERATAC Offset UNI-Interface for Aimpoint Sight [T0970-0000]1 x VFG Barrel Cleaning Felts for 4-4.5mm (Box of 500)1 x ERATAC M-Lok Adaptor for HK Hook [T5500-0000]1 x Contessa QD Mount for HIK-Micro Panther (Picatinny)1 x Krieghoff Spares Kit1 x Ex-Demo Teague Choke Tube, K-80 Parcours #3 (20)1 x Ex-Demo Teague Choke Tube, K-80 Parcours #3 (19)1 x Krieghoff Navy Canvas Gun Slip1 x Contessa Picatinny Rail - Tikka M690/M695 (0 MOA)1 x Contessa Picatinny Rail - Sauer 90 (0 MOA)1 x Ex-Demo Teague Choke Tube, K-80 Parcours #0 (17)2 x Ex-Demo Teague Choke Tube, K-80 Parcours #2+ (15)1 x Contessa Picatinny Rail - Tikka M590/M595 (0 MOA)1 x Krieghoff Trigger Screw1 x Schultz & Larsen Take Down Rifle Case1 x Contessa Picatinny Rail - Tikka M55 (0 MOA)1 x Contessa Picatinny Rail - Remington 700 Long Extended (0 MOA)1 x Schultz & Larsen Picatinny Rings 30mm, 4mm BH, Alu2 x Krieghoff C-Clips (E-Clips)1 x VFG Intensive Barrel Cleaning Felts for 8.5mm (Box of 40)1 x Silva Dine Duo Kit - Purple/White1 x VFG Intensive Barrel Cleaning Felts for .44 (Box of 30)1 x K-80 Forward Position Trigger - Black Titanium2 x Contessa Tikka T3 Euro Rail Base for Quick Release Mount1 x Contessa Picatinny Rail - Tikka T3 / T3X (20 MOA)1 x Contessa Picatinny Rail - Sako 75/85 Medium - Extended1 x Contessa Picatinny Rail - Tikka T1 / T1X (20 MOA)1 x Recknagel Picatinny Rail Tikka T3 / T3X, 20 MOA, Alu [..2081]1 x Krieghoff K-80 Sport Logo Cap Black & Red1 x Black Barrel Case (83cm Internal)1 x Krieghoff Fine Leather Gun Case (K-80 Parcours)1 x Clearance Americase Cordura Case Cover (32x11x3")1 x Krieghoff 12b Choke Wrench1 x VFG Adaptor for US Rods 8-32 UNC (.22 and Over)1 x ERATAC Offset Picatinny to UNI-Interface Adaptor [T0530-0000]1 x Contessa Picatinny Rail - Remington 700 Short Extended (0 MOA)1 x Contessa One Piece QD Picatinny Mount for Swarovski Rail1 x VFG Intensive Barrel Cleaning Felts for 9.3mm (Box of 40)1 x VFG Adaptor for VFG Rods Brass
Manufacturers
Useful Information