Krieghoff Barrel / Stock Stickers

£2.50
20% VAT incl.

Available Options

  • Model:BARREL-STICKER
Krieghoff Barrel / Stock Stickers
Available in Gold, Silver or White.

These high quality vinyl sticker with the "Krieghoff" text logo are designed to be transferred to your Krieghoff Barrels or Stock.

The stickers come as a set of two. So you can attach one either side of your barrels, or attach one to your barrel and one to your stock.

Size: 149mm x 17.5mm
Choose your colour from the drop-down menu above.

How to Apply your Stickers

Step 1 - Prepare It
Lay your sticker on a clean and flat surface with the backing tape (white side) face down and rub over the application tape (clear side) with your squeegee or credit card to ensure the application tape has a good bond to the vinyl letters.

Step 2 - Peel It
Check the positioning of where your sticker will go, so you're ready for the next stage.
Next, peel the application tape (clear side) away from the backing paper (white side). Your sticker letters will now be held by the application tape.
Carefully place the the application tape on to your barrels. Check the alignment as you place it down.

Step 3 - Rub It
While your sticker in laying on your barrels in position, start by rubbing over the application tape and letters gently, and then increase the pressure and firmly rub with your squeegee or credit card. Make sure you cover each letter thoroughly.

Step 4 - Remove It
Carefully peel away the application tape at an angle and corner to corner. The letters should all be transferred onto your barrel. If they are still attached to the application tape, lay the application tape back down and rub over the letter again with the squeegee or credit card. Now, try again until the whole sticker has been transferred.
Your new Krieghoff Barrel / Stock Sticker should now be in place and ready to show off.
If your letters are not coming away from the application tape as you're peeling the application tape off, lay the application tape back over the letter and use the squeegee to rub over the letter again.

Sticker Removal
If you decide to remove the stickers for any reason. Use some light heat such as a hair dryer to aid the removal. The adhesive is permanent but will not damage or mark your barrels. Do not use any abrasive materials or solvents to remove the stickers as this may cause damage to the finish of your barrels.

Postage
We send the Krieghoff Barrel & Stock Stickers with a piece of card to prevent the stickers from being damaged in transit.



You might also like...

2 x Krieghoff "K" Denim Cap - Grey2 x Krieghoff Woven Fabric Patch2 x Krieghoff K-80 Sport Logo Cap Navy & Red2 x Krieghoff K80 Speed Wrench for Factory Chokes1 x Contessa Chromed Picatinny Rail - Sako 75/85 X-Short, Adjustable (20 MOA)1 x Parker Hale Thread to 8-32 Thread Converter1 x Krieghoff HIVIZ Pro Sights1 x Contessa Tactical Picatinny Ring Mount, Brown (with Rail) - 30mm1 x Krieghoff Brass Front Sight Bead2 x Krieghoff K-Diamond Beanie - Navy1 x Krieghoff 28b Choke Wrench1 x AG3 / 392A Alkaline Batteries (10 Pack)1 x Briley 20b Speed Wrench - For Krieghoff1 x Gerber Metolius Pocket Folder1 x Briley 12b Speed Wrench - For Briley Spectrum Chokes1 x Walkstool Steady2 x Krieghoff Spares Kit1 x Krieghoff Front Sight Bead (Small)1 x Teague Precision Choke Key1 x Jones Original Pad Adjuster1 x Ebony & Brass 20 Bore Snap Caps1 x Used Nightforce NP2-DD 8-32x56 Rifle Scope1 x Used Sako P94S, Wooden Stock (.22 LR)1 x K-80 Standard Trigger - Gold Titanium1 x Black Barrel Case (83cm Internal)1 x Anschütz Biathlon Harness1 x K-80 Standard Trigger - Black Titanium1 x Krieghoff K-Diamond Beanie - Burgundy1 x Krieghoff 2018 DTL Badge (Collectors Badge)1 x Krieghoff Stock - Parcours Non-Adjustable, LH, Cat C1 [8280]1 x Ziegler Quick Release Mount for Blaser - Zeiss Rail1 x AA x 4 Camelion Plus Alkaline Batteries1 x Contessa QD Mount for ATN 4K Night Vision (Blaser)1 x Recknagel Weaver Bases - FFV Carl Gustaf 2000 [.-3028]1 x Custom Rifles of Great Britain by Bruce Potts1 x Contessa QD Mount for Blaser R8/R93 for Schmidt & Bender Rail1 x Contessa QD Ultra Low Blaser Mount for Pulsar Night Vision1 x Recknagel Spare Ring Cap Screw M3.5 x 7.4mm [..0880]1 x Contessa Spare Rail Screws 6-48 x 8.5mm Long1 x Krieghoff Stock Removal Wrench1 x Schmierfix Grease by Liqui Moly1 x Ex-Display Gerber GDC Zip Hex1 x Contessa Picatinny Rail - Sako A7 Short (20 MOA)1 x Gerber Myth Series Fixed Saw1 x K-80 Forward Position Trigger - Steel1 x Krieghoff Shell Bag1 x Krieghoff Trigger Screw1 x Gerber Basic Fixed Blade Serrated1 x K-80 Standard Trigger - Gold Plated1 x Krieghoff Fine Leather Gun Case (K-80 Parcours)1 x K-80 Standard Trigger - Steel1 x Gerber Gator Combo Replacement Saw1 x Ziegler Quick Release Mount for Blaser - 1 inch Rings1 x Krieghoff Stock - Parcours Non-Adjustable, LH, Cat 03 [8525]
Manufacturers
Useful Information